JN0-363 Practice Exam Tests Latest Updated on Oct-2023

Pass JN0-363 Exam in First Attempt Guaranteed Dumps!

If you are looking to become an expert in service provider routing and switching, the Juniper JN0-363 exam is an excellent choice. It covers a wide range of topics and requires a deep understanding of networking fundamentals and Juniper Networks technologies. With the right preparation and dedication, passing JN0-363 exam can help you advance your career and demonstrate your expertise to potential employers.

The JN0-363 exam is a comprehensive test that covers a wide range of topics related to service provider routing and switching. JN0-363 exam focuses on the practical application of Juniper Networks technologies in real-world scenarios. The JNCIS-SP certification validates the candidate's ability to design, implement, and troubleshoot Juniper Networks service provider networks.

 

NEW QUESTION # 157
Which two statements are true about IBGP on MX Series devices? (Choose two.)

• A. Interface Lo0 must be used for peering
• B. It is loop free by default
• C. It does not support multihop
• D. Neighbors can be located anywhere within the AS

Answer: B,D

Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/topic-map/bgp-ibgp-peering.html

NEW QUESTION # 158
Exhibit

The LSP is not establishing correctly.
Referring to the exhibit, what should you do to solve the problem?

• A. Enable traffic engineering for the OSPF protocol.
• B. Enable traffic engineering for the RSVP protocol.
• C. Enable traffic engineering for the IS-IS protocol.
• D. Enable traffic engineering for the BGP protocol.

Answer: B

NEW QUESTION # 159
Referring to the exhibit, which firewall filter action(s) will be applied to incoming frames to ge-1/0/3?

• A. Frames will be counted initially by filterA and then counted by filterB.
• B. Frames will be counted by filterA only.
• C. Frames will be counted by filterB only.
• D. Frames will be counted initially by filterB and then counted by filterA.

Answer: A

NEW QUESTION # 160
What is the Junos default router priority advertisement value for IS-IS?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: D

Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/concept/routing-protocol-is-is-security-designated-router-understanding.html#:~:text=If%20routers%20in
%20the%20network,a%20priority%20value%20of%2064.

NEW QUESTION # 161
What is the TTL value for EBGP?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: D

NEW QUESTION # 162
You notice that a route from internal BGP peer 192.168.1.1 is missing from the local route table.Which two commands would be used to help identify the source of the problem? (Choose two.)

• A. show route receive-protocol bgp 192.168.1.1
• B. show route bgp
• C. show route protocol bgp hidden
• D. show route advertising-protocol bgp 192.168.1.1

Answer: A,C

NEW QUESTION # 163
Exhibit

Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?

• A. 172.18.1.0/24
• B. 172.26.4.0730
• C. 192.168.1.3
• D. 192.108.1.4

Answer: B

NEW QUESTION # 164
Click the Exhibit.


You are using OSPF as your IGP in your network. You have applied the OSPF configuration shown in the exhibit to router R1.
Which statement is true in this scenario?

• A. Router R3 will not have a route to subnet 172.16.3.0/24.
• B. Router R1 will send a default route to router R2.
• C. Router R1 must be configured as a stub area for Area 0.0.0.0.
• D. Router R2 will not have a route to subnet 172.16.4.0/24.

Answer: A

NEW QUESTION # 165
Click the Exhibit button.

Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?

• A. the statically assigned address
• B. the link-local address
• C. the loopback address
• D. the multicast address

Answer: B

NEW QUESTION # 166
A customer pays for the bandwidth on a per-packet basis. The network administrator wants to constrain costs and prevent Layer 2 loops on a multihomed Layer 2 WAN network.
Which technology would satisfy these requirements?

• A. Loop protection
• B. Rapid Spanning Tree Protocol
• C. MPLS over GRE
• D. Multiple Spanning Tree Protocol

Answer: A

NEW QUESTION # 167
Click the Exhibit button.

Referring to the exhibit, which statement is correct?

• A. Interface ge-1/0/0.0 can only form a single adjacency
• B. Interface ge-3/0/0.0 has a default metric of 10
• C. Interface xe-0/0/0.0 can only form a single adjacency
• D. Interface xe-0/0/0.0 has a default metric of 10

Answer: A

NEW QUESTION # 168
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of the routers.Which three configuration elements are minimally required in the baseline? (Choose three.)

• A. protocols rsvp for the appropriate interfaces
• B. protocols mpls for the appropriate interfaces
• C. family mpls on the transit interfaces
• D. family mpls on the loopback interface
• E. protocols ldp for the appropriate interfaces

Answer: A,B,C

NEW QUESTION # 169
Click the Exhibit.

The router with the configuration shown in the exhibit has two interfaces, both of which are operational and can pass traffic. These interfaces are connected to two different routers, both of which are configured for OSPF area 0.0.0.1. The router has received LSAs and can now send traffic into the backbone area.
Which two statements are correct? (Choose two.)

• A. The router has two OSPF adjacencies.
• B. The router is an ABR.
• C. The router is an ASBR.
• D. The router has only a single OSPF adjacency.

Answer: B,D

NEW QUESTION # 170
Click the Exhibit.

By default, at which router will the implicit null (Label3) action take place for LSP shown in the exhibit?

• A. R2
• B. R3
• C. R4
• D. R1

Answer: B

NEW QUESTION # 171
Which standards-based election protocol facilities redundancy in a LAN environment by eliminating a single point failure through the use of master and backup routers?

• A. ISSU
• B. BFD
• C. VRRP
• D. graceful restart

Answer: C

NEW QUESTION # 172
You want the R1 and R3 routers to forward traffic destined to the 203.0.113.0/24 network through R2. Which BGP attribute would you modify to satisfy this requirement?

• A. local preference
• B. origin
• C. MED
• D. community

Answer: C

NEW QUESTION # 173
Which action would you use to connect two virtual switches that are configured on the same router?

• A. Create a VRF routing instance
• B. Create a forwarding routing instance
• C. Connect the virtual switches with a cable
• D. Configure an irb interface

Answer: B

NEW QUESTION # 174
Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

• A. R3 will perform a label swap operation on the transport MPLS label.
• B. Traffic from Network 1 to Network 3 and traffic from Network 1 to Network 4 each need their own unique label-switched path.
• C. R3 will perform a label pop operation on the transport MPLS label.
• D. Traffic from Network 1 to Network 3 and from Network 1 to Network 4 can share the same label- switched path.

Answer: A,C

NEW QUESTION # 175
Click the Exhibit button. Based on the configuration shown in the exhibit, what will be the state of the IS-IS levels on interface ge-0/0/0.100?

• A. Level 1 is enabled and Level 2 is disabled.
• B. Level 1 is disabled and Level 2 is enabled.
• C. Level 1 is enabled and Level 2 is enabled.
• D. Level 1 is disabled and Level 2 is disabled.

Answer: D

NEW QUESTION # 176
Click the Exhibit button.

You are configuring an IBGP group. When you commit your configuration, you receive the error shown in the exhibit.
Which additional configuration parameter must you add to your configuration?

• A. multipath
• B. type external
• C. type internal
• D. export <policy name>

Answer: C

NEW QUESTION # 177
Referring to the exhibit, which firewall filter action(s) will be applied to incoming frames to ge-1/0/3?

• A. Frames will be counted initially by filterA and then counted by filterB.
• B. Frames will be counted by filterA only.
• C. Frames will be counted by filterB only.
• D. Frames will be counted initially by filterB and then counted by filterA.

Answer: A

NEW QUESTION # 178
You are using RSVP to signal an MPLS LSP.
Which statement is true in this scenario?

• A. A primary path must be configured to establish an LSP.
• B. The traffic engineering database must be used for all LSPs.
• C. LSPs can be configured without any traffic engineering constraints.
• D. A secondary path must be configured to establish an LSP.

Answer: C

NEW QUESTION # 179
Click the Exhibit button.

Referring to the exhibit, which two statements are correct? (Choose two.)

• A. The router will remove the 0.0.0.0/0 route from the routing table when any BGP prefixes are present
• B. The router will install the 0.0.0.0/0 route into the routing table when any BGP prefixes are present
• C. The router will install the 0.0.0.0/0 route into the routing table when no BGP prefixes are present
• D. The router will remove the 0.0.0.0/0 route from the routing table when no BGP prefixes are present

Answer: B,D

NEW QUESTION # 180
......

Juniper JN0-363 Certification Exam is designed for professionals who want to validate their skills and knowledge in Service Provider Routing and Switching. Service Provider Routing and Switching, Specialist (JNCIS-SP) certification is intended for individuals who are already familiar with Juniper Networks technologies and want to advance their careers in the service provider industry. The JN0-363 exam covers a wide range of topics, including routing protocols, MPLS, BGP, OSPF, and VPNs. Passing the JN0-363 exam requires a deep understanding of service provider networks and the ability to troubleshoot complex issues.

 

JNCIS-SP Free Certification Exam Material from VCE4Dumps with 265 Questions: https://www.vce4dumps.com/JN0-363-valid-torrent.html

JN0-363 Dumps Full Questions - Exam Study Guide: https://drive.google.com/open?id=1v7u0eRV7i94wSmyvdNDveuZvwcZsYsg7