Excellent 300-510 Updated 2021 Dumps With 100% Exam Passing Guarantee
Best way to practice test for Cisco 300-510
NEW QUESTION 59
Refer to the exhibit.
While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?
- A. Modify the router ID to be the interface IP on the serial.
- B. Set the network type in S1/0 to point-to-point.
- C. Modify the IP address or mask of the interface to a valid one.
- D. Set up a priority different than 0 in the interface.
Answer: C
NEW QUESTION 60
Refer to the exhibit.
After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?
- A. Routes that have originated through AS 65517 have the local preference set to 150.
- B. Routes that have passed through AS 65517 have the local preference set to 150.
- C. Routes directly attached to AS 65517 have the local preference set to 150.
- D. Routes that have passed through AS 65517 have the local preference set to 150 and the traffic is denied.
Answer: B
NEW QUESTION 61
Refer to the exhibit.
An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?
- A. Router 1 must have the keyword included in the redistribution command for all EIGRP routes to be redistributed.
- B. Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.
- C. Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.
- D. Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.
Answer: A
NEW QUESTION 62
Refer to the exhibit. Which LSA type is indicated by this router output?
- A. type 4 LSA
- B. type 3 LSA
- C. type 1 LSA
- D. type 2 LSA
Answer: C
NEW QUESTION 63
Refer to the exhibit.
Which tree does multicast traffic follow?
- A. shared tree
- B. source tree
- C. MDT default
- D. MDT voice
Answer: C
NEW QUESTION 64
Refer to the exhibit.
After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship What is the reason tor the problem?
- A. The two routers have the same network ID
- B. The two routers cannot authenticate with one another
- C. The two routers have the same area ID.
- D. The two routers have different iS-types
Answer: B
NEW QUESTION 65
What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)
- A. Cisco Express Forwarding must be enabled.
- B. Each tunnel endpoint must support IPv4 and IPv6.
- C. A static IPv4 address must be configured.
- D. A static IPv6 address must be configured.
- E. A dynamic IPv4 address must be configured.
- F. A dynamic IPv6 address must be configured.
Answer: B,C,D
NEW QUESTION 66
Refer to the exhibit.
A network operator wants to expand the segment routing global block in upcoming maintenance. The operator must ensure that the changes to the segment routing global block have no adverse impacts on the prefix-sid associated with the loopback0 interface used within the OSPF domain.
Which command can the operator use to enforce R2 to have a strict prefix-sid assignment to loopback0?
- A. Option D
- B. Option C
- C. Option A
- D. Option B
Answer: B
NEW QUESTION 67
Which two conditions must be met before separate ISPs can provide interdomain multicast routing? (Choose two.)
- A. Each ISP must configure MSDP to connect its individual multicast administrative domain to the domains at other ISPs.
- B. Each ISP must dedicate a single router to handle multicast traffic between providers.
- C. Each ISP must support intradomain multicast routing.
- D. Each ISP must configure its network to use PIM-DM.
- E. Each ISP must replace its RP assignment with a global RP.
Answer: A,C
NEW QUESTION 68 
Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
- A. R3
- B. R2
- C. R4
- D. R5
Answer: B
NEW QUESTION 69
Refer to the exhibit.
Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
- A. The two routers have the same network ID
- B. The two routers are in different subnets
- C. The two routers have password mismatch issues
- D. The two routers are in the same area
- E. The two routers are in different areas
Answer: B,E
NEW QUESTION 70
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time) 0 bytes Which action makes the peering come back up again?
- A. Set up a hello timer higher.
- B. Set up a hold-down timer higher.
- C. Make a soft reset to the peer.
- D. Set up a minimum hold-down timer higher.
Answer: D
NEW QUESTION 71
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
NEW QUESTION 72
Refer to the exhibit.
Which tree does multicast traffic follow?
- A. shared tree
- B. source tree
- C. MDT default
- D. MDT voice
Answer: C
NEW QUESTION 73
Refer to the exhibit.
What is the relationship between Router 1 and Router 2?
- A. Router 1 and Router 2 centrally learn the topology of the network to aid in SR-TE path selection for peers.
- B. Router 2 is the head-end router in an SR-TE tunnel, and it is learning topology of the network from the PCE enabled on Router 1.
- C. Router 1 and Router 2 are participating in SR-TE tunnels and are both head-end routers.
- D. Router 1 centrally learns the topology of the network to aid in SR-TE path selection, and Router 2 is a node that feeds Router 1 topology information.
Answer: B
NEW QUESTION 74
Refer to the exhibit.
Which statement about this configuration is true?
- A. Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS
- B. Router 1 receives only the best path from neighbor 192.168.1.1
- C. Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes
- D. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
Answer: D
NEW QUESTION 75 
Refer to the exhibit. Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 1 must define an explicit path to router 2
- B. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
- C. Router 2 must have a tunnel interface created with router 1 as the destination
- D. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
Answer: B
NEW QUESTION 76
Refer to the exhibit.
Router 1 has attempted to establish a Cisco MPLS TE tunnel to router 2, but the tunnel has failed. Which statement about this configuration is true?
- A. Router 1 must define an explicit path to router 2
- B. Router 1 must have Cisco MPLS TE enabled on interface gigabitethernet0/1
- C. Router 2 must have a tunnel interface created with router 1 as the destination
- D. Router 1 and router 2 must define the RSVP bandwidth reserved on the physical interfaces
Answer: B
NEW QUESTION 77
Refer to the exhibit.
Which two commands must the engineer configure for the company's PIM-PIM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface without affecting normal operation? (Choose two)
- A. enable Auto-RP announcements
- B. enable sparse-mode
- C. enable sparse-dense mode
- D. enable dense mode
- E. enable auto-rp listener
Answer: C,E
NEW QUESTION 78
Refer to the exhibit.
A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?
- A. Option D
- B. Option C
- C. Option A
- D. Option B
Answer: B
NEW QUESTION 79
Refer to the exhibit.
An engineer applied the configuration on R1 to prevent network 192.168.1.0/24 from being propagated outside of area 5. After the change, users have reported they are not able to access any of the application servers that were working before. While checking the routing table of the peer router. The engineer notices R1 stopped propagating any routes outside are 5. Which action must be taken to fix the problem?
- A. Configure an additional filter-list on R1 for inbound traffic to allow external router into area 5.
- B. Change the prefix-list action to permit and add an explicit deny statement for network 192.168.1.0/24
- C. Reconfigure the filter-list statement to apply in the inbound direction
- D. Add a permit statement for 0.0.0.0/0 le 32 to the end of the prefix-list 10 override the implicit deny.
Answer: D
NEW QUESTION 80
Refer to the exhibit.
An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?
- A. Router 1 sends only one best path to neighbor 192 168.1.1.
- B. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- C. Router 1 receives only one best path from neighbor 192.168.1.1
- D. Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes
Answer: B
NEW QUESTION 81
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION 82
......
Implementing Cisco Service Provider Advanced Routing Solutions Certification Sample Questions and Practice Exam: https://www.vce4dumps.com/300-510-valid-torrent.html
Real Exam Questions & Answers - Cisco 300-510 Dump is Ready: https://drive.google.com/open?id=1g1y1bH6iaeuTf3vH1E2hRClgzSrAJoZz