Steps Necessary To Pass The NACE-CIP1-001 Exam from Training Expert VCE4Dumps
Valid Way To Pass CIP Level 1's NACE-CIP1-001 Exam
NEW QUESTION 22
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Purchase Professional Liability Insurance prior to job commencement
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
Answer: A
NEW QUESTION 23
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. In every instance that an item does not meet the specification requirements
- C. When the Inspector deems it to be a significant non-conforming item
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION 24
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION 25
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Presence of weld spatter may produce a false positive
- C. Chloride salt may produce a false positive
- D. Ultra-Violet light may contaminant the surface
Answer: A
NEW QUESTION 26
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To control the evaporation rate
- C. To promote faster cure
- D. To dissolve the resin
Answer: B
NEW QUESTION 27
SSPC SP 1 identifies the use of:
- A. Inorganic solvents
- B. Organic solvents
- C. Biodegradable detergents
- D. A wide variety of materials
Answer: D
NEW QUESTION 28
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Timely, accurate and concise
- D. Submitted before the end of the job
Answer: C
NEW QUESTION 29
Galvanic corrosion occurs on which of the following substrates:
- A. Wood
- B. Fiberglass Reinforced Plastic
- C. Metal
- D. Concrete
Answer: C
NEW QUESTION 30
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
Answer: A
NEW QUESTION 31
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Anode
- C. Reference Cell
- D. Cathode
Answer: C
NEW QUESTION 32
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Placing the gauge along the longitudinal axis
- C. Using a damaged gauge
Answer: A,C
NEW QUESTION 33
A magnetic pull-off type gauge is a good choice when:
- A. When working on non-ferrous metals
- B. Performing an adhesion test
- C. When an intrinsically safe tool is required
- D. Accuracy is not required
Answer: C
NEW QUESTION 34
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Airless spray
- C. Brush
- D. Conventional spray
Answer: C
NEW QUESTION 35
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspectors position is not the majority position
- C. The Inspector is convinced by verifiable facts
- D. Only when directed by the supervisor
Answer: C
NEW QUESTION 36
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Airless spray equipment
- C. Abrasive blast nozzles
- D. Hand tools
Answer: A
NEW QUESTION 37
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Carefully review the document and do the best you can
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Hire a third patty to assist you in understanding the document
- D. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
Answer: A
NEW QUESTION 38
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. telegraphing.
- B. transitioning.
- C. juxtaposing.
- D. monitoring
Answer: A
NEW QUESTION 39
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. calibrate the instrument in the field.
- C. wash your hands before sampling.
- D. avoid placing the sample discs on a surface.
Answer: C
NEW QUESTION 40
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. demonstrate to the contractor how to apply the coating.
Answer: B
NEW QUESTION 41
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Meet with the prospective employer to determine the scope of your role
- C. Review the NACE Attestation prior to making a decision
- D. Advise the prospective employer that you cannot accept the position
Answer: B
NEW QUESTION 42
Inspector's daily reports are used:
Select All That Apply
- A. To provide continuity between inspectors
- B. To help in cases of a coating failure
- C. To aid in arbitration between the contractor and client
- D. By the contractor to estimate the amount of work done that day
Answer: A,B,C,D
NEW QUESTION 43
......
All NACE-CIP1-001 Dumps and Coating Inspector Level 1 Training Courses: https://www.vce4dumps.com/NACE-CIP1-001-valid-torrent.html
Free Test Engine For Coating Inspector Level 1 Certification Exams: https://drive.google.com/open?id=1eKDuadVuPO535cuFfWGZqflSGHn2y9-r